It is important to have your house or permanent structure properly grounded if you have electricity in the building. This can help prevent a fire should lightning strike or some other electrical surge be sent towards the building. Installing a grounding rod properly is very important but also much easier than you might think. There are some regulations in areas on what the requirements are, so be sure to check and see what the rules are in your area. You will also want to ask your utility company to mark where any underground lines are so you avoid hitting them when installing the rod.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
The next step is to dig the hole. Avoid rocky areas or any places that the utility company marked for other lines. The spot you pick should be between one and two feet from the building for it to work the best. If it is too close, it can reduce the effectiveness by putting the surge back into the building.
Next, start digging. If you have the post hole digger, you can use it to get a few feet down. These are better than shovels because you do not need a wide hole, but a deep one. If you only have a shovel it will do, but the hole won't be as deep. Either way, you will get a good start and be on your way.
When the hole is dug, add water. This is to help soften the ground so it will be easier to push the pole into the ground. Being by pushing it by hand. You may have to move it around in a circle to help get it through the packed dirt. There will be one end that is pointed and that one should go into the ground. At some point, you won't be able to hand push it in and will need to move to the next step with the tools.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
Attach the ground wire. It is best to use the special ground clamp that usually comes with the pole. Make sure the end of the ground wire is exposed if it is a shielded wire. Give it enough slack from the electrical panel so it will not come loose if the pole or wire is hit or bumped.
The last step is to fill in the hole. If you have it completely under the ground or exposed by an inch or so, pack the dirt in so it will be protected. Make sure it is low enough that a lawn mower will not hit it with the blades.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
The next step is to dig the hole. Avoid rocky areas or any places that the utility company marked for other lines. The spot you pick should be between one and two feet from the building for it to work the best. If it is too close, it can reduce the effectiveness by putting the surge back into the building.
Next, start digging. If you have the post hole digger, you can use it to get a few feet down. These are better than shovels because you do not need a wide hole, but a deep one. If you only have a shovel it will do, but the hole won't be as deep. Either way, you will get a good start and be on your way.
When the hole is dug, add water. This is to help soften the ground so it will be easier to push the pole into the ground. Being by pushing it by hand. You may have to move it around in a circle to help get it through the packed dirt. There will be one end that is pointed and that one should go into the ground. At some point, you won't be able to hand push it in and will need to move to the next step with the tools.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
Attach the ground wire. It is best to use the special ground clamp that usually comes with the pole. Make sure the end of the ground wire is exposed if it is a shielded wire. Give it enough slack from the electrical panel so it will not come loose if the pole or wire is hit or bumped.
The last step is to fill in the hole. If you have it completely under the ground or exposed by an inch or so, pack the dirt in so it will be protected. Make sure it is low enough that a lawn mower will not hit it with the blades.
About the Author:
Find out how to get a high-quality grounding rod by viewing our web pages today. To access our online catalog of high voltage equipment or to learn more about our certifications, click the links at http://www.rossengineeringcorp.com .
No comments:
Post a Comment