Altering the LED lights inside your preferred controller is rather easy. For each controller you will need a low electrical power soldering iron, 60/40 rosin, a sponge, a pair of pointed tweezers, and your new LEDs. You can use a greater power level iron, but it is safer to start with a low watt so you stay clear of possibly damaging your motherboard. To open a 360 controller, you will need a t8 screwdriver. A small Phillips head screwdriver is made use of for the ps3. When taking the screws from the 360 controller there is a concealed screw discovered inside the battery pack terminal behind the oblong shaped bar code sticker label.
To begin you will should tin the soldering iron. This merely implies to melt rosin on the iron and then cleanse it off with your sponge. When cleaning the iron, I located it works most effectively to obtain the sponge somewhat wet on one side. I such as to cleanse the iron after each action to increase contact.
As soon as you have the screws gotten there are a couple of steps you will want to avoid breaking your controller case. To dismantle the xbox 360 controller, you will have to push in the thumbsticks and carefully pry the controller apart. To prevent losing any of your buttons, I recommend applying a strip of tape to the front of the controller to hold everything in place. After you have done this, you will have to pull the rubber thumb sticks off their system, extract the motherboard, and set every little thing aside so you do not lose anything.
The PS3 controller is rather much easier to disassemble. Once you have the screws removed, you will just pull the two halves apart. Next, you will pull the rubber joysticks off, and pull the tab that links the R's and L's off their clip. You are now prepared to remove the old lights from the motherboard.
To eliminate the LEDs, I like to utilize a method called drifting. To do this, you will have to melt some rosin on the iron till it makes a little bit of bubble on the iron itself. It might appear like it is going to fall off, but do not fret, it will remain on the iron. As soon as you have this done, you will drift the bubble back and forth across the LED to eliminate it. This will most likely take simply a couple of seconds and the LED will stick to the rosin. Then you will simply cleanse the iron off and duplicate the process for each light.
Applying the new LEDs is a little more difficult than taking them off. First, you will need to consider the bottom of the new LED and determine which side the arrow on the bottom is pointing. You will have to point the arrow toward the adverse side of the motherboard. If you could not figure this out, turn the power to the controller on and the LED will brighten if you have actually correctly lined it up. I such as to leave the battery pack and the back half of the controller linked. This is so I could make use of the contact pad to turn the controller on. For the ps3, you can simply plug in the charging cable. As soon as you have straightened them properly, you will use your tweezers to hold the LED in place and simply include a little rosin to both side and you are done. It may spend some time however a little practice will make things a whole lot easier. Now you prepare to display your recently light controller with your favorite color lights!
To begin you will should tin the soldering iron. This merely implies to melt rosin on the iron and then cleanse it off with your sponge. When cleaning the iron, I located it works most effectively to obtain the sponge somewhat wet on one side. I such as to cleanse the iron after each action to increase contact.
As soon as you have the screws gotten there are a couple of steps you will want to avoid breaking your controller case. To dismantle the xbox 360 controller, you will have to push in the thumbsticks and carefully pry the controller apart. To prevent losing any of your buttons, I recommend applying a strip of tape to the front of the controller to hold everything in place. After you have done this, you will have to pull the rubber thumb sticks off their system, extract the motherboard, and set every little thing aside so you do not lose anything.
The PS3 controller is rather much easier to disassemble. Once you have the screws removed, you will just pull the two halves apart. Next, you will pull the rubber joysticks off, and pull the tab that links the R's and L's off their clip. You are now prepared to remove the old lights from the motherboard.
To eliminate the LEDs, I like to utilize a method called drifting. To do this, you will have to melt some rosin on the iron till it makes a little bit of bubble on the iron itself. It might appear like it is going to fall off, but do not fret, it will remain on the iron. As soon as you have this done, you will drift the bubble back and forth across the LED to eliminate it. This will most likely take simply a couple of seconds and the LED will stick to the rosin. Then you will simply cleanse the iron off and duplicate the process for each light.
Applying the new LEDs is a little more difficult than taking them off. First, you will need to consider the bottom of the new LED and determine which side the arrow on the bottom is pointing. You will have to point the arrow toward the adverse side of the motherboard. If you could not figure this out, turn the power to the controller on and the LED will brighten if you have actually correctly lined it up. I such as to leave the battery pack and the back half of the controller linked. This is so I could make use of the contact pad to turn the controller on. For the ps3, you can simply plug in the charging cable. As soon as you have straightened them properly, you will use your tweezers to hold the LED in place and simply include a little rosin to both side and you are done. It may spend some time however a little practice will make things a whole lot easier. Now you prepare to display your recently light controller with your favorite color lights!
No comments:
Post a Comment